Table of contents
- Before you start
- Beginner's Guide
- Downloads
- Configuration
- Compatibility
- Telemetry
- WHOOP Section
- Troubleshooting
- SilverHardware
- Go Brushless
- Tuning a quad
- Quadcopter mods
- Merchandise
- Links
Sidebar
playground:playground
This is an old revision of the document!
Welcome to Silverware wiki
This Wiki should introduce and help in and on a project, RCGroups user silverxxx has started in september 2015
Features:
- Acro mode
- Level mode (switchable via TX channel or gestures, using stock TX)
- Telemetry via Bluetooth using SilverVISE
- Telemetry using a DEVO and Bayang Telemetry Protocol (Telemetry support since the December '16 nightly builds of Deviation)
- Telemetry using Taranis/9X/TH9X
- Brushless motor Driver supporting PWM, PPM, Oneshot and DShot
- Inverted flight possibility on Floureon H101 / Eachine H8S
- Well suitable for custom builds, such as different frames, larger motors, Hexas, Brushless. Most compatible boards are known to drive 8520 coreless motors without issues
- Switchable output to switch 'something' on and off during flight via TX (e.g. FPV gear)
- Buzzer support (watch the mod section) for lost quad detection
- 2S support for the green and blue H8 boards (don't use 1S brushed motors! For brushless only recommended, you might fry the FETs otherwise!
The quads everything started with
Compatibility list
| Quad | H8 acro/dual | H101 acro/dual | CG023 | Other | Notes |
|---|---|---|---|---|---|
| Eachine/JJRC H8, green board | yes | ||||
| Eachine H8 3D mini | yes 3D(code) | ||||
| Floureon H101 | yes | ||||
| Eachine H8S | yes | ||||
| Eachine CG023 | yes | ||||
| Eachine/JJRC H8, blue board | yes | [1] | Keil Bug, solve it that way, CLK/DAT swapped | ||
| GW008 Skull Quad | yes, forum post | ||||
| DHD D1 | info | acro only | |||
| Bayang X9, GD F130 mcu board | yes (post) | motor order changed, 16k flash | |||
| Eachine 3D X4, CG027R board | yes | ||||
| FQ777-124 | yes (post) | bikemike's fork | |||
| CX Model CX023 | yes (post)_PARATABLE_INS_ and following| | | |bikemike's fork hardware_cx023.h..zip| </sortable> See the OpenMicro (CG023) Hardware compatibility charts for more detailed list of possible and work in progress compatibility. ==== Common info links, including how to start ==== |Flashing guide video| | |Changing config settings.| | |Changing the target device.| | |Guide to installing required software.| | |Download the GigaDevice GD32F130 support pack.| | |Flashing guide video / Blue Board| | |Gallery of awesome pictures with few ways on how to do the flashing port.| | | | | ^Silverware H8/H101 thread.| | |Github H8 dual source| | |Github H8 acro source| | |Github Floureon H101 dual source| | |Hexa using H101 FC (Circular Style)| | |Hexa using H101 FC (H Style)| | |Tricopter using H8 FC+| | |H101 "Rattitude" Version| | ^Silverware CG023 thread| |Github CG023 dual source| |Github DHD D1 source acro only(beta)| |CG023 firmware wiki page| ==== Beginner's Guide ==== Differences between Level and Acro - why does the quad what it does? ==== Transmitter config ==== Stock Transmitter Config Devo Config ==== FAQ ==== === Flashing === ^Question^Answer| |“Error, Flash download failed - Could not load file '/.axf”|Project not compiled, go to 'Project → Build Target (or press F7). Errors in code may be causing compilation to fail. Check that the number of errors is zero when compiling.| |“No target connected”|Quad not powered on, you need to supply power to the board; either plug the battery, or the serial cable. If powered, check your clk and data connections. This message indicates the computer can't communicate to the quadcopter.| |“Unknown target connected”|Wrong chip selected, go to “Project → Options For Target (Alt + F7)”._PARATABLE_INS_New window opens, switch to 'Debug' tab and on top right, press “ST-Link Debugger” Settings button. New window opens, switch to 'Flash Download' tab, select the proper chip family, press Remove, then Add, and then select the proper chip. | ||||
| Internal Command Error. Error: Flash Erase failed - Target DLL has been cancelled“ | Your programming wires might be too long. Try to keep them as short as possible. | ||||
| ST-link USB communication error or similar popup | Disconnect/reconnect st-link or Restart computer. This may also be a special blue board problem. read here | ||||
| Select device menu grayed out | This is from video, use text instructions from post, or skip the related steps |
Firmware settings
| Question | Answer |
|---|---|
| What PWM frequency is the best? | The pwm frequency changes the linearity of the motors (due to their inductance) and as such it can have an effect on flight. For 720 motors 8Khz seems to result in linear thrust. Some 6mm motors are similar. Increasing frequency reduces thrust at low throttle, so it can help with wobbles that occur while descending. 820 motors are still somewhat nonlinear even at 32Khz |
Flight
| Question | Answer |
|---|---|
| My quad is drifting in flight | Try the accelerometer calibration: Place the copter on a level surface, throttle low, roll&yaw center, and pitch down three (3) times in quick succession. The LEDs will blink alternating while the calibration is in process. |
| How do I fly acro without crashing all the time? | “There is an art to flying, or rather a knack. Its knack lies in learning to throw yourself at the ground and miss. … Clearly, it is this second part, the missing, that presents the difficulties.” |
PID tuning
Where to buy stuff?
STlink, spare props, good quality motors, batteries and so on.
We all no doubt know the joys of the slow boat from China but hey they are cheap and available at Banggood
Mods
Changing firmware settings
Debug mode
Brushless setups
playground/playground.1492542462.txt.gz · Last modified: 2017/04/18 21:07 by sirdomsen
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
