Differences

This shows you the differences between two versions of the page.

--- gallery [2017/10/30 02:26]
scruffy1 [Flashing port examples]
+++ gallery [2017/11/18 15:25] (current)
scruffy1 [Flashing port examples]
@@ Line 2: / Line 2: @@
 Note: the board pads are not designed for mechanical support, it's best to use a wire size that will break before the pad will. Attaching a solid part to the pad with no other support can result in the pad ripped from the board after a crash.
 ==== Flashing port examples ====
@@ Line 8: / Line 7: @@
 == Male 2.54cm header. ==
-{{:dscf0588.jpg?200x200}}{{:img_20151111_090745.jpg?200x200}}
+{{:dscf0588.jpg?200x200|dscf0588.jpg}}{{:img_20151111_090745.jpg?200x200}}
 == Female 2.54cm header. ==
-{{:img_20151221_194838.png?200x200}}{{:img_20160514_155237.jpg?200x200}}{{:img_20160514_155126.jpg?200x200}}
+{{:img_20151221_194838.png?200x200}}{{:img_20160514_155237.jpg?200x200|User comments}}{{:img_20160514_155126.jpg?200x200|User comments}}
 == Picoblade connector. ==
-{{:h3-1.jpg?200x200}}{{:p1010597-s.jpg?200x200}}
+{{:h3-1.jpg?200x200|h3-1.jpg}}{{:p1010597-s.jpg?200x200|p1010597-s.jpg}}
 == Solid wire (24gauge?). ==
-{{:img_20160507_231834544.jpg?200}}{{:datalink.png?200}}
+{{:img_20160507_231834544.jpg?200|img_20160507_231834544.jpg}}{{:datalink.png?200}}
 == CG023 FC with silverxxx firmware on a 110mm brushless quad ==
-{{:cf110mma.jpg?200x200}}
+{{:cf110mma.jpg?200x200|cf110mma.jpg}}
 h8s-3d, using a 2mm round pin female micro connector
-the final photo also shows power lead out for akk bs2 camera (whoopin' it up ! )
+nothing of the connector is outside the shell, so hopefully this, and being on the side of the machine renders it "safe" from impact
+the final two photos also show the power lead out for akk bs2 camera (whoopin' it up ! )
+{{:50079de59b11a255d9b47db82d1c2028.jpg}}{{:48d6379213b5285a0669439a7ac1e32d.jpg}}{{:85f1b6db6058d3b7cfd1b178d7a04840.jpg}}{{:e2806c56da49655dc1daaf196212198d.jpg}}.
+h8 mini with blue board (note that the clk and dat pads are incorrectly labelled on the board : they are reversed)
+using the same female micro connector as for the h8s-3d; both connect to the ST-link v2 with the same modified servo plug > male micro connector, with ground plug closest to the rear (near the battery "hatch")
-{{:50079de59b11a255d9b47db82d1c2028.jpg}}{{:48d6379213b5285a0669439a7ac1e32d.jpg}}{{:85f1b6db6058d3b7cfd1b178d7a04840.jpg}}
+{{:img_2274.jpg?300x400|initial soldering}}{{:img_2275.jpg?400x300|secured with epoxy and microballoons}}{{:img_2276.jpg?nolink&400|finished port}}{{:img_2277.jpg?nolink&400|and again; depron plugs over led's act as diffusers to improve visibility}}

Silverware Wiki

User Tools

Site Tools

Differences

Page Tools