Differences

This shows you the differences between two versions of the page.

--- gallery [2016/05/30 02:38]
ian446 [Flashing port examples]
+++ gallery [2017/11/18 15:25] (current)
scruffy1 [Flashing port examples]
@@ Line 1: / Line 1: @@
 ===== Gallery of awesome pictures =====
+Note: the board pads are not designed for mechanical support, it's best to use a wire size that will break before the pad will. Attaching a solid part to the pad with no other support can result in the pad ripped from the board after a crash.
 ==== Flashing port examples ====
-==Male 2.54cm header.==
-{{::dscf0588.jpg?200x200|}}{{::img_20151111_090745.jpg?200x200|}}
+== Male 2.54cm header. ==
-==Female 2.54cm header.==
-{{::img_20151221_194838.png?200x200|}}{{:img_20160514_155237.jpg?200x200|}}{{:img_20160514_155126.jpg?200x200|}}
+{{:dscf0588.jpg?200x200|dscf0588.jpg}}{{:img_20151111_090745.jpg?200x200}}
-==Picoblade connector.==
-{{::h3-1.jpg?200x200|}}{{::p1010597-s.jpg?200x200|}}
+== Female 2.54cm header. ==
-==Solid wire (24gauge?).==
-{{::img_20160507_231834544.jpg?200|}}{{::datalink.png?200|}}
+{{:img_20151221_194838.png?200x200}}{{:img_20160514_155237.jpg?200x200|User comments}}{{:img_20160514_155126.jpg?200x200|User comments}}
-==CG023 FC with silverxxx firmware on a 110mm brushless quad==
-{{::cf110mma.jpg?200x200|}}
+== Picoblade connector. ==
+{{:h3-1.jpg?200x200|h3-1.jpg}}{{:p1010597-s.jpg?200x200|p1010597-s.jpg}}
+== Solid wire (24gauge?). ==
+{{:img_20160507_231834544.jpg?200|img_20160507_231834544.jpg}}{{:datalink.png?200}}
+== CG023 FC with silverxxx firmware on a 110mm brushless quad ==
+{{:cf110mma.jpg?200x200|cf110mma.jpg}}
+h8s-3d, using a 2mm round pin female micro connector
+nothing of the connector is outside the shell, so hopefully this, and being on the side of the machine renders it "safe" from impact
+the final two photos also show the power lead out for akk bs2 camera (whoopin' it up ! )
+{{:50079de59b11a255d9b47db82d1c2028.jpg}}{{:48d6379213b5285a0669439a7ac1e32d.jpg}}{{:85f1b6db6058d3b7cfd1b178d7a04840.jpg}}{{:e2806c56da49655dc1daaf196212198d.jpg}}.
+h8 mini with blue board (note that the clk and dat pads are incorrectly labelled on the board : they are reversed)
+using the same female micro connector as for the h8s-3d; both connect to the ST-link v2 with the same modified servo plug > male micro connector, with ground plug closest to the rear (near the battery "hatch")
+{{:img_2274.jpg?300x400|initial soldering}}{{:img_2275.jpg?400x300|secured with epoxy and microballoons}}{{:img_2276.jpg?nolink&400|finished port}}{{:img_2277.jpg?nolink&400|and again; depron plugs over led's act as diffusers to improve visibility}}

Silverware Wiki

User Tools

Site Tools

Differences

Page Tools