Silverware Wiki

User Tools

Site Tools

Trace:
devo_config

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
devo_config [2016/07/21 20:14]
sirdomsen [DEVO 7e] 		devo_config [2019/01/09 20:40] (current)
sirdomsen [Hints for DIY model files]
Line 1: Line 1:
 +<font inherit/inherit;;#FF0000;;inherit>Note: H101 model files are backwards compatible with other Silverware quads, just the 3D throttle stuff needs to be disabled/ignored</font>
 +
 ==== DEVO 7e ==== ==== DEVO 7e ====
  
Line 9: Line 11:
 === H101 === === H101 ===
  
-[[http://www.rcgroups.com/forums/showpost.php?p=34814600&postcount=2270|Model file]] for H101 dual mode firmware with 3D throttle enabled posted by SirDomsen (likely incompatible with Silverware Versions newer than 2016-05-19)+[[http://www.rcgroups.com/forums/showpost.php?p=34814600&postcount=2270|Model file]] for H101 dual mode firmware with 3D throttle enabled posted by SirDomsen
  
 [[http://www.rcgroups.com/forums/showpost.php?p=34905121&postcount=2490|Another one]] with 3D throttle, posted by HappyHarry [[http://www.rcgroups.com/forums/showpost.php?p=34905121&postcount=2490|Another one]] with 3D throttle, posted by HappyHarry
Line 18: Line 20:
 //#define NATIVE_INVERTED_MODE //#define NATIVE_INVERTED_MODE
 </code> </code>
 +
 ==== Devo 7e with Switchmod ==== ==== Devo 7e with Switchmod ====
  
 Devo 7E model file with switchable stagility/rattitude mode by RCGroups user Markus Gritsch Devo 7E model file with switchable stagility/rattitude mode by RCGroups user Markus Gritsch
  
-He got inspired by Mike Meyer and added stagility/rattitude/horizon mode to my Devo 7E model file. It requires a modded Devo 7E with two additional 3x switches.\\ +He got inspired by Mike Meyer and added stagility/rattitude/horizon mode to his Devo 7E model file. It requires a modded Devo 7E with two additional 3x switches. 
-\\+
 HOLD:\\ HOLD:\\
 0: normal\\ 0: normal\\
-1: throttle hold\\ +1: sticky throttle hold (see [[http://www.deviationtx.com/forum/how-to/1953-how-to-create-a-sticky-throttle-hold|http://www.deviationtx.com/forum/how-to/1953-how-to-create-a-sticky-throttle-hold]] for more info) 
-\\+
 SWA:\\ SWA:\\
 0: linear positive throttle over the full stick range\\ 0: linear positive throttle over the full stick range\\
 1: positive throttle only in the upper stick range halve\\ 1: positive throttle only in the upper stick range halve\\
-2: inverted throttle in the lower stick halve, normal throttle in the upper stick halve\\ +2: inverted throttle in the lower stick halve, normal throttle in the upper stick halve – CP heli trainer 
-\\+
 SWB:\\ SWB:\\
 0: level/angle mode, linear roll and pitch\\ 0: level/angle mode, linear roll and pitch\\
-1: stagility/rattitude/horizon mode\\ +1: stagility/rattitude/horizon mode (change threshold on Ch10, Page 2)\\ 
-2: rate/acro mode, expo on the roll and pitch channels\\ +2: rate/acro mode, expo on the roll and pitch channels 
-\\+
 FMOD:\\ FMOD:\\
 0: low rates\\ 0: low rates\\
 1: high rates 1: high rates
  
 +Throttle trim buttons are used to turn the LEDs on/off
 +
 +{{:wiki:h101.zip|H101/H8mini model file & config.h}}
 +
 +==== DEVO 7 with Goebish's NRF24_multipro ====
  
-====DEVO 7 with Goebish's NRF24_multipro==== 
 [[https://github.com/goebish/nrf24_multipro|link to Goebish's Code]] [[https://github.com/goebish/nrf24_multipro|link to Goebish's Code]]
  
Line 51: Line 58:
  
 You have to assign the Channels in Bayang.ino (multimodule Arduino-Sketch) to be as follows: You have to assign the Channels in Bayang.ino (multimodule Arduino-Sketch) to be as follows:
-  packet[2] = GET_FLAG(AUX3, BAYANG_FLAG_FLIP)            //Assignment for Devo7 + Silverware + 
-                  | GET_FLAG(AUX2, BAYANG_FLAG_HEADLESS) +<code> 
-                  | GET_FLAG(AUX1, BAYANG_FLAG_RTH) +packet[2] = GET_FLAG(AUX3, BAYANG_FLAG_FLIP)            //Assignment for Devo7 + Silverware 
-                  | GET_FLAG(AUX6, BAYANG_FLAG_SNAPSHOT)  //Not assigned in available in DEVO 7 +                | GET_FLAG(AUX2, BAYANG_FLAG_HEADLESS) 
-                  | GET_FLAG(AUX5, BAYANG_FLAG_VIDEO); +                | GET_FLAG(AUX1, BAYANG_FLAG_RTH) 
-        packet[3] = GET_FLAG(AUX4, BAYANG_FLAG_INVERT)     +                | GET_FLAG(AUX6, BAYANG_FLAG_SNAPSHOT)  //Not assigned in available in DEVO 7 
 +                | GET_FLAG(AUX5, BAYANG_FLAG_VIDEO); 
 +      packet[3] = GET_FLAG(AUX4, BAYANG_FLAG_INVERT) 
 +</code>
  
 H101 has to be configured as descripted [[http://www.rcgroups.com/forums/showpost.php?p=34189408|here]] H101 has to be configured as descripted [[http://www.rcgroups.com/forums/showpost.php?p=34189408|here]]
  
- +==== DEVO 10 ====
-====DEVO 10====+
  
 [[http://www.rcgroups.com/forums/showpost.php?p=34189408|H101 model file]] for using H101 as a CP-Heli Trainer posted by SirDomsen [[http://www.rcgroups.com/forums/showpost.php?p=34189408|H101 model file]] for using H101 as a CP-Heli Trainer posted by SirDomsen
  
 +==== Hints for DIY model files ====
 +
 +watch the [[:config.h|config.h section]]
 +
 +H8 icons for Devo
  
-====Hints for DIY model files==== +[[http://www.rcgroups.com/forums/showpost.php?p=35608494&postcount=76|rcgroups]]
-watch the [[config.h|config.h section]]+
  
  
-others coming soon 
devo_config.1469124893.txt.gz · Last modified: 2016/07/21 20:14 by sirdomsen

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki