Silverware Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
<font inherit/inherit;;#FF0000;;inherit>Note: H101 model files are backwards compatible with other Silverware quads, just the 3D throttle stuff needs to be disabled/ignored</font>

==== DEVO 7e ====

=== H8 mini ===

[[http://www.rcgroups.com/forums/showpost.php?p=33653759|Model file]] for H8mini dual mode firmware posted by syvic

[[http://www.rcgroups.com/forums/showpost.php?p=34409628|Model file]] for H8mini dual mode firmware posted by WardoMon

=== H101 ===

[[http://www.rcgroups.com/forums/showpost.php?p=34814600&postcount=2270|Model file]] for H101 dual mode firmware with 3D throttle enabled posted by SirDomsen

[[http://www.rcgroups.com/forums/showpost.php?p=34905121&postcount=2490|Another one]] with 3D throttle, posted by HappyHarry

for inverted controls like on a CP-Heli comment in

<code>
//#define NATIVE_INVERTED_MODE
</code>

==== Devo 7e with Switchmod ====

Devo 7E model file with switchable stagility/rattitude mode by RCGroups user Markus Gritsch

He got inspired by Mike Meyer and added stagility/rattitude/horizon mode to his Devo 7E model file. It requires a modded Devo 7E with two additional 3x switches.

HOLD:\\
0: normal\\
1: sticky throttle hold (see [[http://www.deviationtx.com/forum/how-to/1953-how-to-create-a-sticky-throttle-hold|http://www.deviationtx.com/forum/how-to/1953-how-to-create-a-sticky-throttle-hold]] for more info)

SWA:\\
0: linear positive throttle over the full stick range\\
1: positive throttle only in the upper stick range halve\\
2: inverted throttle in the lower stick halve, normal throttle in the upper stick halve – CP heli trainer

SWB:\\
0: level/angle mode, linear roll and pitch\\
1: stagility/rattitude/horizon mode (change threshold on Ch10, Page 2)\\
2: rate/acro mode, expo on the roll and pitch channels

FMOD:\\
0: low rates\\
1: high rates

Throttle trim buttons are used to turn the LEDs on/off

{{:wiki:h101.zip|H101/H8mini model file & config.h}}

==== DEVO 7 with Goebish's NRF24_multipro ====

[[https://github.com/goebish/nrf24_multipro|link to Goebish's Code]]

Inverted Flight like a CP-heli!!

{{:wiki:h101.rar|Download DEVO7 model file}}

You have to assign the Channels in Bayang.ino (multimodule Arduino-Sketch) to be as follows:

<code>
packet[2] = GET_FLAG(AUX3, BAYANG_FLAG_FLIP)            //Assignment for Devo7 + Silverware
                | GET_FLAG(AUX2, BAYANG_FLAG_HEADLESS)
                | GET_FLAG(AUX1, BAYANG_FLAG_RTH)
                | GET_FLAG(AUX6, BAYANG_FLAG_SNAPSHOT)  //Not assigned in available in DEVO 7
                | GET_FLAG(AUX5, BAYANG_FLAG_VIDEO);
      packet[3] = GET_FLAG(AUX4, BAYANG_FLAG_INVERT)
</code>

H101 has to be configured as descripted [[http://www.rcgroups.com/forums/showpost.php?p=34189408|here]]

==== DEVO 10 ====

[[http://www.rcgroups.com/forums/showpost.php?p=34189408|H101 model file]] for using H101 as a CP-Heli Trainer posted by SirDomsen

==== Hints for DIY model files ====

watch the [[:config.h|config.h section]]

H8 icons for Devo

[[http://www.rcgroups.com/forums/showpost.php?p=35608494&postcount=76|rcgroups]]
Silverware Wiki

User Tools

Site Tools

Page Tools
