Note: H101 model files are backwards compatible with other Silverware quads, just the 3D throttle stuff needs to be disabled/ignored ==== DEVO 7e ==== === H8 mini === [[http://www.rcgroups.com/forums/showpost.php?p=33653759|Model file]] for H8mini dual mode firmware posted by syvic [[http://www.rcgroups.com/forums/showpost.php?p=34409628|Model file]] for H8mini dual mode firmware posted by WardoMon === H101 === [[http://www.rcgroups.com/forums/showpost.php?p=34814600&postcount=2270|Model file]] for H101 dual mode firmware with 3D throttle enabled posted by SirDomsen [[http://www.rcgroups.com/forums/showpost.php?p=34905121&postcount=2490|Another one]] with 3D throttle, posted by HappyHarry for inverted controls like on a CP-Heli comment in //#define NATIVE_INVERTED_MODE ==== Devo 7e with Switchmod ==== Devo 7E model file with switchable stagility/rattitude mode by RCGroups user Markus Gritsch He got inspired by Mike Meyer and added stagility/rattitude/horizon mode to his Devo 7E model file. It requires a modded Devo 7E with two additional 3x switches. HOLD:\\ 0: normal\\ 1: sticky throttle hold (see [[http://www.deviationtx.com/forum/how-to/1953-how-to-create-a-sticky-throttle-hold|http://www.deviationtx.com/forum/how-to/1953-how-to-create-a-sticky-throttle-hold]] for more info) SWA:\\ 0: linear positive throttle over the full stick range\\ 1: positive throttle only in the upper stick range halve\\ 2: inverted throttle in the lower stick halve, normal throttle in the upper stick halve – CP heli trainer SWB:\\ 0: level/angle mode, linear roll and pitch\\ 1: stagility/rattitude/horizon mode (change threshold on Ch10, Page 2)\\ 2: rate/acro mode, expo on the roll and pitch channels FMOD:\\ 0: low rates\\ 1: high rates Throttle trim buttons are used to turn the LEDs on/off {{:wiki:h101.zip|H101/H8mini model file & config.h}} ==== DEVO 7 with Goebish's NRF24_multipro ==== [[https://github.com/goebish/nrf24_multipro|link to Goebish's Code]] Inverted Flight like a CP-heli!! {{:wiki:h101.rar|Download DEVO7 model file}} You have to assign the Channels in Bayang.ino (multimodule Arduino-Sketch) to be as follows: packet[2] = GET_FLAG(AUX3, BAYANG_FLAG_FLIP) //Assignment for Devo7 + Silverware | GET_FLAG(AUX2, BAYANG_FLAG_HEADLESS) | GET_FLAG(AUX1, BAYANG_FLAG_RTH) | GET_FLAG(AUX6, BAYANG_FLAG_SNAPSHOT) //Not assigned in available in DEVO 7 | GET_FLAG(AUX5, BAYANG_FLAG_VIDEO); packet[3] = GET_FLAG(AUX4, BAYANG_FLAG_INVERT) H101 has to be configured as descripted [[http://www.rcgroups.com/forums/showpost.php?p=34189408|here]] ==== DEVO 10 ==== [[http://www.rcgroups.com/forums/showpost.php?p=34189408|H101 model file]] for using H101 as a CP-Heli Trainer posted by SirDomsen ==== Hints for DIY model files ==== watch the [[:config.h|config.h section]] H8 icons for Devo [[http://www.rcgroups.com/forums/showpost.php?p=35608494&postcount=76|rcgroups]]