Silverware Wiki

User Tools

Site Tools

Trace:
more_brushless_setup_info3

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
more_brushless_setup_info3 [2016/08/28 12:08]
ian446 		more_brushless_setup_info3 [2018/04/28 10:38] (current)
ian446
Line 1: Line 1:
-This little 99mm diagonal quad was built using Eachine 1104 4000kv motors, Multistar 6A esc's, H8 mini green FC (cut down), RX2535 props, 450mAh 3S Nanotech battery and a 99mm frame from Armattan Productions. It weighs 46.9gm and the battery is 40.0gm, AUW is 86.9gm. +Placeholder.
- +
-{{https://dl.dropboxusercontent.com/u/61170900/AP99_1115a.JPG?nolink&900x865}} +
- +
-Some of the firmware settings are - gyro lpf 42Hz, soft lpf none, throttle reduction 30%, motor min 0.07 for 3S, motor filter on, PWM 8kHz. One of the esc's has a 5V BEC and that powers the FC. It's a good flyer on 2S or 3S. +
- +
-<code>The current PID's are: +
-float pidkp[PIDNUMBER] = { 6.3e-2 ,  6.3e-2 ,  2.6e-1 }; +
-float pidki[PIDNUMBER] = { 1.8e-1 ,  1.8e-1 ,  1.0e-1 }; +
-float pidkd[PIDNUMBER] = { 2.9e-1 ,  2.9e-1 ,  1.4e-1 };</code> +
- +
-{{https://dl.dropboxusercontent.com/u/61170900/AP99_1117a.JPG?nolink&900x865}} +
- +
- +
- +
- +
-This next quad was built using a GW008 (skull drone) FC with CG023 firmware, buck regulator from Banggood, DYS 1306 4000kv motors, Gemfan 3545 props, XM10A escs, 450mAh 3S Nanotech battery and a 140mm frame from Armattan Productions. It weighs 99.9gm and the battery is 40.7gm, AUW is 140.6gm. The other battery I use is an 850mAh 3S weighing 71.5gm, AUW 171.4gm. +
- +
-{{https://dl.dropboxusercontent.com/u/61170900/AP140_1112a.JPG?nolink&900x865}} +
- +
-Some of the firmware settings are - gyro lpf 41Hz, soft lpf 2nd 88Hz, motor filter on, PPM ESC freq 400Hz, HW I2C speed fast, motor min 0.12. +
- +
-<code>The current PID's (tuning is still in progress): +
-float pidkp[PIDNUMBER] = { 4.0e-2 ,  4.0e-2 ,  1.4e-1 }; +
-float pidki[PIDNUMBER] = { 1.7e-1 ,  1.7e-1 ,  0.7e-1 }; +
-float pidkd[PIDNUMBER] = { 3.9e-1 ,  3.9e-1 ,  1.5e-1 };</code> +
- +
-{{https://dl.dropboxusercontent.com/u/61170900/AP140_1113a.JPG?nolink&1280x634  }} +
  
more_brushless_setup_info3.1472378896.txt.gz · Last modified: 2016/08/28 12:08 by ian446

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki